Encore N150 Uživatelský manuál

ENHWI-N3 802.11n Wireless Router User Manual 1

VIII - PC Network Adapter Setup (Windows XP) • Assuming your PC or Laptop is equipped with a Network Interface Card. Click on START Æ select “Contr

• Click to Highlight the “Internet Protocol (TCP/IP)” then click “Properties” button • Select the “General” tab. a. ENHWI-N3 supports the DHCP f

IX - Power up the ENHWI-N3 Connect the supplied power-adapter to the power port and connect it to a wall power outlet. The ENHWI-N3 automatically e

A welcome screen will pop up a few seconds and then will disappear. 13

NOTE: The product picture may be different from what you have Click Setup Wizard to run basic setup settings of your ENHWI-N3. Click User Manual to

Setup Wizard Click to proceed. Click <Exit> to abort. 15

Make sure your DSL/CABLE modem is setup and working prior to this installation procedures. If not, call your Internet Service Provider and have them

Check the MODEM and ENHWI-N3 connection. It should be as shown below. 17

Check power connection for modem as well as ENHWI-N3. Make sure the antenna is connected to rear panel of ENHWI-N3. Click <Next> to proceed. N

Click to configure WAN & Wireless settings. 19

TABLE OF CONTENTS 1 INTRODUCTION ...

Enter the factory default username is admin and password is also admin. Click to continue. Your default browser screen will connect to the ENHWI-N3

Select the mode your ENHWI-N3 is going to use. The Setup Wizard will skip the WAN configuration under AP Repeater Mode. Click and your ENHWI-N3 will

The Smart Wizard will detect the DHCP and PPPoE connections automatically. In the picture above it shows that the Smart Wizard detected a DHCP server

Here, you can configure the host name and MAC address of the ENHWI-N3. The “Clone MAC Address” button clones the MAC address of your PC and use it as

Setting up Wireless LAN Enter the name for your wireless network SSID (the default is ENCORE59FE74) and security key (default is 1234567890). Move an

To save configuration changes click NOTE: After the Wireless settings are saved and the ENHWI-N3 is rebooted, you need to reconnect your WLAN clien

XI – How to login to the ENHWI-N3 web based Graphical User Interface The ENHWI-N3 use a web based user interface for setting up your router’s config

ENHW-N3 Home Page Screen XII - The AP Router Mode  SYSTEM Shows the Uptime, Hardware information, Serial number as well as the Firmware ver

1. WAN Settings: Scroll down to see the full information. This section displays whether the WAN port is connected to a Cable / DSL modem. It also

2. LAN Settings: Scroll down to see this section. Displays the ENHWI-N3 Router LAN port’s current information. It also shows whether the DHCP Server i

I - Introduction Congratulations on your purchase of ENHWI-N3 802.11n Wireless Router. ENHWI-N3 is backward compatible with wireless devices runnin

The LAN Tab is where LAN settings can be change. If you are an entry level user, after hooking up the cables, try to access the internet from your co

DHCP Server DHCP Server: This can be enabled or disabled, “Enabled” by default. Lease time: Lease time assigned to all IP address by the DHCP serve

the <Refresh> button to update the available information. Click the <Refresh> button to get the updated table. You can click to put a ch

settings. The “Schedule” table screen lists the pre-scheduled services. Select any of the schedules by using the check box located on the right side o

On this “Event Log” screen, it displays all events and events information occurred after the start-up. Scroll down to see more. The Event Log can be

z Language Tab This is where you select preferred language. 35

 WIZARD Click Wizard to configure the basic functionalities of the ENHWI-N3 Router. A popup Setup Wizard Window will be immediately displayed. If th

- Dynamic IP Use the MAC address when registering for the Internet service, and do not change it unless required by your ISP. If your ISP use

Host Name: This is optional. MAC address: The default value is set to the WAN’s physical address or MAC of the broadband router. - Static IP If

- Point-to-Point Protocol over Ethernet(PPPoE) 39

II - Key Features Features Advantages Incredible Data Rate up to 150 Mbps** Easily handled heavy data loads such as MPEG audio / video streaming,

Login / Password: Enter the PPPoE username and password assigned by your ISP Provider. Service Name: This is optional. Maximum Transmission Unit (

PPTP allows the secure connection over the Internet by simply dialing in to a local point provided by your ISP provider. The image screen allows cli

Radio: You can turn on/off wireless radio. If wireless Radio is turned off, the ENHWI-N3 will not take wireless connections. Mode: Three operation m

ESSID1 to ESSID4: ESSID is the name of your wireless network. It is recommended to use a unique name to identify your wireless device in the LAN. This

MAC address 1~4: Please enter the MAC address(es) of the neighboring APs that participates in the WDS. A maximum of 4 devices are allowed. Set Sec

- Advanced On this tab you can set the advanced wireless settings. If you’re in doubt what to enter or use here, leave these settings as it is. This

DTIM Period: Default value is 1. Enter a value between 1 and 255 for the Delivery Traffic Indication Message (DTIM). A DTIM is a countdown informing c

ESSID Selection: ENHWI-N3 router supports multiple ESSID, you can name your wireless ESSID here. Broadcast ESSID: If you enabled “Broadcast ESSID

IEEE 802.1x is an authentication protocol using RADIUS server. When this is Enabled, every LAN user must use an account to login to this Access Point

Authentication Type: There are two authentication types: "Open System" and "Shared Key". Both AP and wireless client must be con

III - Package Contents Check and make sure that none of the items listed below are missing. Do not discard the packing materials, in case of return;

64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or 5-digit ASCII character as the encryptio

WPA-RADIUS Encryption Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS server to authenticate wireless

- MAC Address Filtering This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network.

Click <Apply> at the bottom of the screen to save the above configurations. - Wi-Fi Protected Setup™ (WPS™) WPS™ is the simplest way to estab

WPS Current Status: If the wireless security (encryption) function of this wireless router is properly set, you’ll see a ‘Configured’ message here. O

- Client List WLAN Client Table shows the Wireless clients associated to this Wireless Router. - Policy The Broadband router can allow you to set

 FIREWALL The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker atta

- Demilitarized Zone (DMZ) If you have a client PC that cannot run an Internet application (e.g. Games) properly behind the NAT firewall, then you c

The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and Sync Flood. If Interne

Enable MAC Filtering: Check to enable or disable MAC Filtering. Deny: If you select “Deny” then all clients will be allowed to access Internet exce

IV - Product Layout Front Panel View LED Lights Description POWER Lights up in Red when powered ON. Blinks on TEST/RESET WLAN Lights

Add PC MAC Address Fill in “LAN MAC Address” and <Description> of the PC that is allowed / denied to access the Internet, and then click <A

- IP Filter Enable IP Filtering: Check to enable or uncheck to disable IP Filtering. Deny: If you select “Deny” then all clients will be allowe

select the PC you want to remove in the table and then click <Delete Selected>. If you want to remove all PCs from the table, just click the <

Remove URL Keyword If you want to remove some URL keywords from the "Current URL Blocking Table", select the URL keyword you want to remo

 ADVANCED - Network Address Translation (NAT) Network Address Translation (NAT) allows multiple users at your local LAN site to access the Internet

Enable Port Mapping: Enable or disable port mapping function. Description: description of this setting. Local IP: This is the local IP of the serv

Fill in the "Local IP", “Protocol”, “Port Range” and "Description" of the setting to be added and then click "Add". Then

Enable Port Forwarding: Enable or disable Port Forwarding. Description: The description of this setting. Local IP / Local Port: This is the LAN Cli

Fill in the "Description" , "Local IP", "Local Port", "Protocol" and “Public Port” of the setting to be added

Enable Trigger Port: Enable or disable the Port Trigger function. Trigger Port: This is the outgoing (Outbound) range of port numbers for this partic

Rear View Item Description Reset Press and release this button to reboot the device. Press and hold this button for 10 seconds to l

Add Port Triggering Fill in the "Trigger Port", "Trigger Type”, “Public Port”, "Public Type", "Public Port" and

- UPNP With UPnP, all PCs in you Intranet will discover this router automatically. So, you don’t have to configure your PC and it can easily acc

Enable / Disable UPnP: You can enable or Disable the UPnP feature here. After you enabled the UPnP feature, all client systems that support UPnP, lik

Unlimited Priority Queue: The LAN IP address will not be bounded in the QoS limitation. High/Low Priority Queue: This can put the packets in the

Type: Specify the direction of packets. Upload / Download or both. IP range: Specify the IP address range. You could also fill one IP address Protoco

- Routing You can set Enable Static Routing to let the router forward packets using your routing policy. Destination LAN IP: Specify the destin

Subnet Mask: Specify the Subnet Mask of static routing rule. Default Gateway: Specify the default gateway of static routing rule. Hops: Specify the Ma

Remote management Allows you to designate a host in the Internet. The ability to configure the Broadband router from a remote site. Enter the designa

Time Zone: Select the time zone of the country you are currently located. The router will set its time based on your selection. NTP Time Server: T

PC Date and Time: This field would display your computer’s date and time. Daylight Savings: The router can also take Daylight Savings into account.

V - Network + System Requirements To begin using the ENHWI-N3, make sure you meet the following as minimum requirements: h PC / Notebook Computer

Enable/Disable DDNS: Enable or disable the DDNS function of this router Server Address: Select a DDNS service provider Host Name: Fill in your sta

- Diagnosis In this page lets you run diagnosis to your network status. - Firmware This page allows you to upgrade the router’s fir

Once you’ve selected the new firmware file, click <Apply> at the bottom of the screen to start the upgrade process - Back-up This page al

Backup Settings: This can save the current Broadband router configuration to a file named "config.bin" on your PC. You can also use the &l

XIII - Repeater Mode Repeater mode has limited settings compared to the AP mode. Choose “Repeater mode” on the top right corner of the configurati

LAN Settings: This page displays the Broadband router LAN port’s current LAN information. WLAN Settings: Wireless configuration details such as SSID,

802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree function is enabled, this router will use the spanning tree protocol to pre

- Event Log View operations log of the ENHWI-N3. This page shows the current system log of the ENHWI-N3 router. It displays any event occurred after

- Language This Wireless Router supports multiple languages for user interface. Select your preferred language.  Wireless - Basic You can se

Radio: Enable or Disable Wireless function Band: Allows you to set the frequency band of the router. Fix at 802.11b, 802.11g or 802.11n modes. You c

VII - Setup LAN, WAN LAN connection: Connect Ethernet cable between your PC/Notebook LAN port & one of the 4 available LAN ports on ENHWI-N3.

- Client List This WLAN Client Table shows the Wireless client associated to this Wireless Router. - Policy The Broadband router allows you to

Communication between Wireless clients and wired clients: This function allows the Wireless Client to communicate with other Wireless Client in the

Old Password: Fill-in the current password to be replaced. This is required to allow changing to a new password. New Password: Enter your new pass

NTP Time Server: Enter the NTP Time Server address or URL here. This also accepts local the IP address if the NTP Time Server is on the same LAN. Day

- Diagnosis This page lets you diagnose the connection problem and the network status by executing the Ping function. The result tells you whether th

The saved backup can be restored again if needed by sing the Restore Settings selection and browse the saved backup file to restore back to the expe

- Reset You can software reset the broadband router when system stops responding or stop working. This is different from the hardware reset that ca

z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. z Consult the dealer or an experienced r